600 GPD Direct Flow Reverse osmosis water system with LCD controller and automatic membrane flushing.
No Tank Needed.
Drinking water quality.
Operated via LCD display that shows when membranes (filters) should be replaced, Water temperature, PPM reading and the opportunity to auto flush the system through the LCD display.
It comes with a Leak system detector that can be placed where you want it.
These RO units are ideal for under sink drinking water, aquariums, small café, food preparation, hydroponics, and light window cleaning.
Please note: The pump, membranes and other parts are intended for domestic or light commercial use and not intended for continual heavy duty use,
If needed to be used for a longer period of continued use, maximum 2-3 hours at a time with a cooling-off period of 1 hour.
1. Pump 80 Psi
2. Metal Bracket with stand
3. Automatic Flushing
4. Solenoid valve system
5. Membranes 3x 200GPD Membrane
1. 10-inch 5-micron PP filter
2. 10-inch carbon block CTO filter
3. 10-inch 1-micron PP filter
4. 380 GPD RO membrane (3x 200GPD Membranes)
5. Active carbon post filter
Reverse osmosis is a method of purifying water by pushing it through a semi-permeable membrane, the membrane allows pure water molecules through it, whilst impurities are flushed away. By using reverse osmosis, it is possible to remove all suspended solids, up to 98% of dissolved solids and virtually all bacteria, pesticides and viruses. Reverse osmosis has many benefits.
At the heart of any reverse osmosis system is the membrane, water is forced under pressure through the membrane to a storage tank and the waste by-product goes to drain. In addition to the membrane reverse osmosis unit also incorporates pre-filters. Because filtered RO water is produced very slowly it is necessary to store the treated water in a tank or container to supply filtered RO water as and when it is required.
Reverse osmosis units do require a minimum water pressure of 2.7 bar/40psi - so it is essential you have your source water pressure assessed before purchasing the unit.
This RO system will remove up to 99% of tap water contaminants.
Typical removal rates (%)
Sodium (99%), Calcium (99%), Magnesium (99%), Potassium (98%), Iron (99%), Manganese (99%), Aluminium (99%), Ammonium (97%), Copper (99%), Nickel (99%), Zinc (99%), Cadmium (99%), Silver (98%), Mercury (98%), Barium (99%), Chromium (99%), Lead (99%), Chloride (99%), Bicarbonate (98%), Nitrate (97%), Fluoride (98%), Silicate (98%), Phosphate (99%), Chromate (99%), Cyanide (95%), Sulphate (99%), Bromide (98%), Arsenic (99%), Selenium (99%), Bacteria (99%), Protozoa (99%), Amoebic Cysts (99%), Giardia (99%), Asbestos (99%), Oestrogen (99%), Sediment / Turbidity (99%)
Important information to consider prior to ordering.
Our Reverse Osmosis Systems are shipped fully assembled complete with a comprehensive instruction manual for easy DIY installation with no plumbing experience required.
The effectiveness and productivity of RO systems increase with greater water pressure and temperature. The actual flow rate (in GPD) of any reverse osmosis system depends on your source water pressure and temperature.
While manufacturers state that 60 psi is required at the membrane for full production, we know that not everyone's cold water is at 60 psi and 30 °C therefore, we remind you that you might get less than the stated GPD from your membrane, perhaps 50% or even less if your pressure and temperature are very low!
If flow rate is critical for you, you need to consider all these factors before choosing membrane size.
Temperature: membranes are designed to operate between 13 °C - 30 °C
Water pressure: Min 40 psi, Optimum 60 psi,
Chlorine content of no more than 0.1 ppm
TDS up to 1000 ppm
PH 2 - 11