400 GPD Direct Flow Reverse osmosis water

400 GPD Direct Flow Reverse osmosis water

400 GPD Direct Flow Reverse osmosis water

400 GPD Direct Flow Reverse osmosis water

  • £255.95

  • Ex Tax: £213.29

400 GPD Direct Flow Reverse osmosis water system with LCD controller and automatic membrane flushing. 




Drinking water quality.


Operated via LCD display that shows when membranes (filters) should be replaced, Water temperature, PPM reading and the opportunity to auto flush the system through the LCD display. 


Comes with a Leak system detector that can be placed where you want it.


 System's Futures:



1. Pump 80 Psi 

2.  Metal Bracket with stand

3. Automatic Flushing

4. Solenoid valve system


5. Membranes 2x400GPD

 


 Filters


1. 10-inch 5-micron PP filter


2. 10-inch carbon block CTO filter


3. 10-inch 1-micron PP filter


4. 400 GPD RO membrane (2x 400 Membrane for 800 GPD)


5. Active carbon post filter


Please note if you prefer to have a DI Resin filter instead of the post-carbon filter let us know


Also we can provide to order larger systems ie: 1200, 1400, 1600 GPD




Description


Reverse osmosis is a method of purifying water by pushing it through a semi-permeable membrane, the membrane allows pure water molecules through it, whilst impurities are flushed away. By using reverse osmosis, it is possible to remove all suspended solids, up to 98% of dissolved solids and virtually all bacteria, pesticides and viruses. Reverse osmosis has many benefits.


At the heart of any reverse osmosis system is the membrane, water is forced under pressure through the membrane to a storage tank and the waste by-product goes to drain. In addition to the membrane reverse osmosis unit also incorporates pre-filters. Because filtered RO water is produced very slowly it is necessary to store the treated water in a tank or container to supply filtered RO water as and when it is required.


Reverse osmosis units do require a minimum water pressure of 2.7 bar/40psi - so it is essential you have your source water pressure assessed before purchasing the unit.


This RO system will remove up to 99% of tap water contaminants.


 


Typical removal rates (%)


Sodium (99%), Calcium (99%), Magnesium (99%), Potassium (98%), Iron (99%), Manganese (99%), Aluminium (99%), Ammonium (97%), Copper (99%), Nickel (99%), Zinc (99%), Cadmium (99%), Silver (98%), Mercury (98%), Barium (99%), Chromium (99%), Lead (99%), Chloride (99%), Bicarbonate (98%), Nitrate (97%), Fluoride (98%), Silicate (98%), Phosphate (99%), Chromate (99%), Cyanide (95%), Sulphate (99%), Bromide (98%), Arsenic (99%), Selenium (99%), Bacteria (99%), Protozoa (99%), Amoebic Cysts (99%), Giardia (99%), Asbestos (99%), Oestrogen (99%), Sediment / Turbidity (99%)


 


Important information to consider prior to ordering.


Our Reverse Osmosis Systems are shipped fully assembled complete with a comprehensive instruction manual for easy DIY installation with no plumbing experience required.


The effectiveness and productivity of RO systems increase with greater water pressure and temperature. The actual flow rate (in GPD) of any reverse osmosis system depends on your source water pressure and temperature.


While manufacturers state that 60 psi is required at the membrane for full production, we know that not everyone's cold water is at 60 psi and 77 degrees F therefore, we remind you that you might get less than the stated GPD from your membrane, perhaps 50% or even less if your pressure and temperature are very low!


If flow rate is critical for you, you need to consider all these factors.

Write a review

Please login or register to review

Tags: 400 GPD Direct Flow Reverse osmosis water